SFP+ 10G 1310nm 10KM

Product Features

Duplex LC Connector

Support hot-pluggable

Metal with lower EMI

Excellent ESD protection

DFB Transmitter and PIN Receiver

Distance up to 10Km on 9/125um SMF

Single 3.3V power supply and Low power dissipation <1.2W

GR-253-CORE compliant

RoHS Compliant and Lead-Free 

Compliant with IEEE 802.3ae

Compliant with SFP+ MSA: SFF-8431 Rev4.1

Compliant with SFF-8472 Rev11.0

Applications

10GBASE-LR/LW

10G Fibre Channel

Other optical link

Product Selection

Regulatory Compliance

ESD to the Electrical PINs: compatible with MIL-STD-883E Method 3015.7

ESD to the LC Receptacle: compatible with IEC 61000-4-2 GR-1089-CORE

Immunity compatible with IEC 61000-4-3

EMI compatible with FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B

Laser  Eye  Safety  compatible  with  FDA  21CFR  1040.10  and  1040.11  EN60950,  EN  (IEC) 60825-1,2

RoHS compliant with 2002/95/EC 4.1&4.2 2005/747/EC

Pin Descriptions

Notes:

1. The module signal ground contacts, VeeR and VeeT, should be isolated from the module case.

2. This contact is an open collector/drain output and should be pulled up to the Vcc_Host with  resistor in the range 4.7KΩ to 10KΩ . Pull ups can be connected to one or several power supplies, however the  host  board  design  shall ensure that  no  module  contact  has  voltage  exceeding  module VccT/R +0.5V.

3. Tx_Disable is an input contact with a 4.7KΩ to 10KΩ pull-up resistor to VccT inside module.

4. Mod_ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull the contact up to Vcc_Host with a resistor in the range from 4.7KΩ to 10KΩ . Mod_ABS is asserted “High ” when the SFP+ module is physically absent from a host slot.

5. RS0 and RS1 are module inputs and are pulled low to VeeT with > 30 kΩ resistors in the module. RS0 optionally selects the optical receive signaling rate coverage. RS1 optionally selects the  optical transmit signaling rate coverage.

These contacts can also be used for RS0 and RS1 if implementing SFF8079. See SFF8079 for details. RS1 is commonly connected to VeeT or VeeR in the classic SFP modules. The host needs to ensure that it will not be damaged if this contact is connected to VeeT or VeeR in the module.

The  SFP+  module  provides  two  inputs  RS0  and  RS1  that  can  optionally  be  used for  rate selection. RS0 controls the receive path signalling rate capability, and RS1 controls the transmit path signalling rate capability. The host and module may choose to use either, both, or none of these functions. Because contact 9 in the classic SFP INF-8074i is connected to VeeR, an SFP+ host utilizing RS1 must provide short circuit protection.

This  rate  select  functionality  can  also  be  controlled  by  software  as  defined  by  SFF-8472. Optionally the rate select methods of Part 2 of SFF-8079 may be used instead of the method described  here  by  setting  the  management  declaration  bit  (A0h  byte  93  bit  2)  to   1,  see SFF-8472.

Pin-out of Connector Block on Host Board

Recommend Circuit Schematic

Absolute Maximum Ratings

Recommended Operating Conditions

Electrical Characteristics

Optical Characteristics

Notes:

1.   BER  ≤10-12  @PRBS231-1 at 10.3125Gb/s.

2.   For the APSP31B33CDL10

3.   For the APSP31B33IDL10

Mechanical Specifications

EEPROM Information

EEPROM memory map specific data field description is as below: